Indesit Washing Machines - Recent Questions, Troubleshooting & Support


Hi,

Demo Mode
If the machine is on Demo mode 'D on' will be displayed and the machine will NOT function.
To reset the machine for normal use:·
Turn the power off at the wall.
Push in and hold down the Start/Stop and the Start/Reset
buttons, while still holding down, turn the machine on at the
wall.
'D off' will be displayed and the machine will function
normally.

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Vr2020 ' and have a nice day!!

Indesit Washing... | Answered on Jan 27, 2019


Behind the kick panel under the door latch should be a red cable to pull down.

Indesit IWC61451... | Answered on Jan 26, 2019


Disconnect machine from mains power. Take off lid and reach down, see if you can release the door from there. What model is your machine?

Indesit WA 115... | Answered on Jan 24, 2019


Greetings from Canada!

After Sales Services - Shaker Group


www.shaker.com.sa/en/after-sale-services

The largest fleet of After-Sales Services of Shaker Group in the KSA ... brands like Indesit, Ariston, Maytag, Bissell and Midea in Saudi Arabia and many ... technical support through the full network ofservice centers throughout the kingdom.

Service Centers - Shaker Group


www.shaker.com.sa/en/maintenancecenters

Indesit. Cookers; Built-In; Dishwashers; Laundry. Midea. Refrigerators; Small Domestic ... Riyadh. Omar ben Al-Khatab St. Next to Ministry of Finance. Location on the map ... in king Fahad road - king Abdulaziz Street opposite of Alnahdah sportclub, before Hail center ... Al Khaldiyah District, In front of new Arab Bank.

SOLVED: Service center saudi arabia - Vr2020


www.fixya.com/support/t23789694-service_center_saudi_arabia 1 answer
Mar 11, 2014 - service center saudi arabia MODEL WIDXL 106 CONTROL BOARD - IndesitWashing Machines question.

Support - Indesit


https://www.indesit.ae/Pages/Support

to help you manage, maintain and service your appliances, and keep ... Indesit UAE Customer Service. Having trouble with your Indesit appliance? We're here ...

Indesit Washing... | Answered on Jan 05, 2019


Make sure that you disconnect the machine from the mains BEFORE attempting ANY repairs.
Remove the top of the machine [there are usually 2 or 3 screws at the back], and this will give you access to the inlet water valves.
Check the sort of solenoid fill valve that you have on your machine, the sort of valve depends on the model of machine, some have twin solenoid valves, and some have triple solenoid valves.
You will now need a Multimeter to check the windings in each of the coils, so if you do not know how to use a meter of this sort, get advice from a professional.
Some faults with these valves cannot be accessed with a meter, as it may be an internal fault with the valve itself ( for example a swollen seal on the plunger), but unless you are experienced with working with live circuits, do not try checking this for yourself, and get professional help. or, just change the valve, and see if that fixes the problem.
If any of these valves has failed, unfortunately you will need to replace the complete valve unit.

Indesit Washing... | Answered on Jan 02, 2019


H20 means not filling with water properly.
Check hoses and that taps are fully turned on , make sure water pressure is o/k, no kinks in hoses

Indesit Washing... | Answered on Dec 29, 2018


I have a maytag washer that when it fills with water it wont drain out..the spin cycle just makes a noise and it wont do anything..any ideas what i can do to fix it thanks

Indesit W 123... | Answered on Dec 29, 2018


No spin, or lite spin try these: bare in mind that many times there is no spin it can be due to a clogged water pump so check it for debris and or broken propeller.

Other items to check Using a multi meter check for continuity the door switch, which when bad may not allow agitation or spin. Bare in mind the lid switch assembly can fail either mechanically or electrically.

Check the clutch, motor coupler, brake assembly, transmission, and mode shifter or actuator. one way to check for slipping is to get under the machine after a spin cycle ( this is if u get a lil spin but not much leaving clothes still wet) mix in a spray bottle a lil water and some dish detergent, then spray it on the clutch assembly ( the metal round pc. Connected to the tranny) if it sizzles and steams up then u know its bad and slipping. Another way to check clutch if u get no spin at all? Is to take it out and use ur hand to try and turn the inner spring assembly pushing it around the inside? If its very easy, it BAD should be hard to push by hand.

Or try the hand test:

If no hammering sound has ever been heard out of this machine, one of the unofficial tests we professional appliantologists will do in the field is called the Hand Test. WARNING:This test is not sanctioned by Whirlpool Corporation; it involves bypassing safety equipment and then putting your hand on and near rotating machinery which could result in injury, dismemberment, disfigurement, disembowelment, mangling, hideous screaming, and a ****** *****. Proceed at your own risk! Have a nice day.

- put the timer on a spin cycle and open the lid- grab the inner basket with maybe 30% to 40% of your hand strength with your left hand
- turn on the machine and bypass the lid switch by depressing the lid switch with a key until the machine begins to spin
- if the clutch is engaging properly, the basket should immediately begin to spin and slip through your hand
- if it takes very little force to stop the tub from spinning, the clutch needs to be replaced.

Next check the motor coupler which engages the tub and tranny to the motor. ( if its bad u usually get no wash or spin or very little of either)

Next if belt driven check for a loose, worn or broken belt. And on some models there is no clutch but rather what is called a splutch. And a MODE shifter. These can go bad and effect the spin cycle.

On some front load models u may need to check the STATOR assembly.
The stator is essentially one half of a motor, it interacts with the tub by creating a strong electro-magnet. If the stator burns out the washer won't spin or agitate. Check the stator for continuity. This part is often misdiagnosed.

Sometimes a no spin machine can be due to a plugged waterpump hose or obstructed water pump propeller. Check these by eye and hand. And in some models check with a meter for continuity and voltage.

LID SWITCH TEST- next step is toremove the cabinetand jumper the lid switch harness (tan to gray). Put the unit in spin and watch the shiny metal clutch disc that is on top of the transmission where the shaft comes out. If the machine starts and runs in spin, check to see if the disc is spinning. If it is, then the problem isnot in the gearcase- look for trouble in theclutch,
basket driveor the tub drive block

If, on the other hand, the disc is NOT spinning, check for a problem withthe motor drive coupleror one of its retainers. This washer doesn't have a belt. Instead, the motor is directly coupled to the gearcase by a drive coupler; that's why it's called a direct drive washer.

Read more:Diagnosing and Repairing Spin and Agitate Problems in a Whirlpool / Kenmore Direct Drive Washer

http://fixitnow.com/wp/2010/07/07/diagnosing-and-repairing-spin-and-agitate-problems-in-a-whirlpool-kenmore-direct-drive-washer/#ixzz3XW7eZwiN
By the way my advice is free cuz God is good!

Washer will not drain:

Thedrain water pumpis the main part in your washing machine that pumps out the water. If this is defective or has failed in any way, this will be the reason why your washer will not drain the water. Before you order a new drain pump, make sure tocheck the pump to be sure a small object like clothing or similar has not lodged itself insideof it causing the NO DRAIN issue and even a no spin issue?. If the drain pump is not clogged, you can test it with a multimeter and remove and replace if needed.

Read more:http://removeandreplace.com/2014/10/30/fix-washing-machine-that-wont-drain-washer-not-draining-water/#ixzz3X2LbXMWJ

The washing machinedrain hoseis where the water flows through to get the water out.If this drain hose is blocked, kinked, bent, or clogged, the washer will NOT be able to remove the waterfrom the tub. Check the drain hose to be sure it allows the water to flow freely. You can take the drain hose off and run water through it in your sink to be sure it is not blocked. If there is water STILL in the washer when you remove the drain hose, grab a bucket as the water will exit from where you disconnected it

Thewater pump belt(to drain out the water) may have broke or become frayed or loose.If this belt breaks then it is unable to drain and remove the water from your washer. Inspect the belt to see if this is causing theNO DRAINissue and remove and replace if needed.

If thelid switchis not working as required it will cause your washer to not drain (and many other problems).This may be unlikely as a bad lid switch will usually cause your washer to alsonot agitate or spin.However on some models this can vary. The best thing to do if you have a suspected bad lid switch is to test it. It can fail electrically and or mechanically. If mechanical failure is the issue, you should be able to see if it is cracked, broken, or not in place to make contact with the lid. To test it electrically, use a multimeter set on Ohms and test it for continuityMy advice is free cuz God is good!














Indesit Washing... | Answered on Dec 09, 2018

Not finding what you are looking for?
Indesit Logo

2,061 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Indesit Washing Machines Experts

shaun taylor

Level 3 Expert

1527 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

jimorris77

Level 3 Expert

411 Answers

Are you an Indesit Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...