Tool & Hardware - Other Repair Questions, Solutions & Tips - Vr2020

Tools & Hardware - Others - Recent Questions, Troubleshooting & Support

Professional-grade varieties are automatic, and fire a nail directly upon pulling the trigger. A semi-automatic nail gun is more appropriate for beginners, since it requires a two step process: pull the trigger and then tap the barrel against the wood. This safety feature protects the user from accidentally firing a nail gun and injuring himself or others.

Arrow... | Answered Yesterday

Hi Elaine, The EasyShot stapler is a bottom load stapler. Please follow the steps below to make sure you are loading the staples correctly.

- Turn the tool upside down so that you can read the text "use light duty narrow crown" on the bottom of the magazine

- Open the magazine of the tool

- Place the staples inside the channel (not on the back of the magazine rail)

- Close the magazine.

Attached is a picture so you can see where to place the staples.

If you are still having trouble please contact our customer service department and we can assist you further.



Staples Tools &... | Answered Yesterday

same way you load and stapler from the rear by removing the spring (holder)

Electric Tools &... | Answered 3 days ago

Go to the hardware shop and buy one

Sander Tools &... | Answered on Oct 14, 2018

Google (shopmate)(2710T0)(manual) without parens.

Tools & Hardware... | Answered on Oct 13, 2018

OK the belt tensioning mechanism is spring loaded. First what is the quality of the belts are they real flimsy or stiff. You say the rollers spin but my question does the rear roller still spin and the belt remain stationary. If so the rubber belt on motor is bad. I would take a look for excessive wear on the rear roller. Does the yoke mechanism snap forward or move slowly, look for a build up of sawdust in this area that might be restricting movement on the yoke. The wear plate in still good condition. One other thing on the belts are they directional? Do they have an arrow on the inside if so that has to point toward front of tool. I looked at a breakdown and could not see anything else to suggest. I never had this problem except with belts when I was at Makita.

Makita 3 x 24"... | Answered on Oct 13, 2018

Check the date of the bottom of the gas. With the gas removed when you fire it you should hear a faint spark sound from the top. If gas is in date try putting it in your pocket for 10 minutes to warm it up. Open the front and make sure the piston is pushed all the way up into the machine.

Hitachi NR90GC2... | Answered on Oct 12, 2018

Google (ozito)(PRG-631VK)(manual) without parens.

Tools & Hardware... | Answered on Oct 12, 2018

Google (tos)(sn50)(manual) without parens.

Tools & Hardware... | Answered on Oct 10, 2018

if the unit can't be adjusted , adjust the air pressure to the machine at the hose regulator

Staples Tools &... | Answered on Oct 10, 2018

Google (Colchester)(1400)(manual) without parens OR contact Colchester directly to request it.

Tools & Hardware... | Answered on Oct 08, 2018

No.. the issue issue is the switch inside. when your Dremel 4200 stop working, press firmly the grey area between the speed selector and the brush housing. I think this a defect in the design of the 4200. 9f840401-fb84-4f7b-8c68-75a9be3ceb9e.jpg


Dremel Tools &... | Answered on Oct 08, 2018

Not finding what you are looking for?
Tools & Hardware - Others Logo

14,354 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Tools & Hardware - Others Experts


Level 3 Expert

83096 Answers

Brad Brown

Level 3 Expert

17490 Answers

john h

Level 3 Expert

17852 Answers

Are you a Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides