Refrigerators - Page 3 - Recent Questions, Troubleshooting & Support


First make sure that the coils ane clean and not restricted. Next make sure the cooling fan is working... If both checks are ok, then you may have a freon problem and need to call a service tech.Make sure the temp controls are set at the right temperture.

Refrigerators | Answered on May 13, 2020


If the code is 14 E then that means: IM sensor error.

Cause: the sensor is read as open or shorted, check the sensor connections and at the main PCB.

Samsung... | Answered on May 12, 2020


When you replaced the thermistor, did you check the resistance of the wiring and temperature sensor back at the control board? If the wires are damaged or the connector at the control board has corrosion, the control board won't get the correct signal information. If those are fine, then the control board is probably faulty. Sears Parts Direct has the control board here: https://www.searspartsdirect.com/product/3jlv6aqwdo-0046-253/id-5304512769 . Other repair shops will have this part as well.

I wish that only the refrigerator temperature sensor was faulty. I hope this helps.

Cindy Wells

Frigidaire... | Answered on May 11, 2020


https://icemakershub.com/ice-maker-not-working/

https://www.youtube.com/watch?v=oyaO_Q6CBUM
Kenmore Ice maker; To reset, shut down the unit and unplug the cord from the socket. Wait for 5-10 minutes to plug your ice maker and start the ice maker by holding down the power button.
https://coolersjunkie.com/portable-ice-maker-wont-make-ice-troubleshooting/

Refrigerators | Answered on May 11, 2020


https://www.youtube.com/watch?v=7i7MZAbatbQ

To check on the water inlet valve, unplug the refrigerator and shut off the water supply to it. ... Or it could be that there's dirt or a defect inside the water inlet valve. See the section here on the water dispenser actuator, and the micro switch, since the problem with the water dispensing could lie there as well.
https://www.fix.com/repair/appliance/refrigerator/not-dispensing-water/



Refrigerators | Answered on May 11, 2020


Unplug the LG fridge and wait 20 minutes - Plug back into power - Many times the code will clear or reset. If not keep reading below... -The majority of the time it is the freezer fan causing the Er FF error code. The FF error code indicates that the freezer fan motor is defective.
https://removeandreplace.com/2017/08/27/lg-refrigerator-error-code-er-ff-how-to-clear/

https://www.lg.com/us/support/help-library/error-codes-refrigerator-CT10000021-1441392048805

LG Refrigerators | Answered on May 11, 2020


How to Turn It off. If you don't care for the alarm, if you're changing the water filter or if the Samsung is experiencing an unusual amount of traffic, deactivate the alarm. Locate the electronic display of the Samsung refrigerator, press the "Alarm" button for three seconds and then release it.
https://www.hunker.com/13409711/my-new-samsung-fridge-wont-quit-beeping
https://www.youtube.com/watch?v=kM6P3rdn5Zo

https://www.youtube.com/watch?v=PLSixFjjuv8

Refrigerators | Answered on May 10, 2020


Sometimes a fridge gets to cold causing ice then it might have warmed up a little so the ice is melting maybe check your temperature gauge to see if its too warm or cold.

Refrigerators | Answered on May 10, 2020


Either the thermostat is failing to switch on the defrost panel at the end of each cooling cycle or the defrost panel has failed...

Westinghouse... | Answered on May 09, 2020


It needs more gas. Call a refrigeration engineer.

LG Refrigerators | Answered on May 08, 2020


I had the same problem. The cause is the digital display is not communicating with the motherboard. What had happened in my case is the plug connection between the door's digital display and the motherboard had become unplugged. The wire running from the motherboard runs below the fridge, and connects via plug located along the bottom of the fridge below the freezer door, connecting to the wire running from the display to the bottom of the freezer door. I just reconnected it and that reset the display. Glad for it too, I thought I needed a new $130 motherboard! Hope this helped!

GE Refrigerators | Answered on May 07, 2020


Good Morning Friend,

I understand you are receiving an "SY EF" code on your Frigidaire refrigerator, model# FRS3R5EMB. The "SY EF" code stands for system error with the evaporator fan. This possibly means that there is something going on with your evaporator fan or it could possibly be a false error code. . I suggest resetting your appliance, by either unplugging it or shutting the power off at your home's circuit breaker, for 3-5 minutes. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your appliances status has changed successfully.

-Best Regards-
WP

Frigidaire... | Answered on May 07, 2020


Try placing sponge pieces around the dispenser to dampen the rattles.

Refrigerators | Answered on May 07, 2020


If you attempt to enter an invalid Program CODE the control will not save the new code, but will beep https://ifacetimeapp.com/

Whirlpool... | Answered on May 07, 2020


If you get the message OF on your Samsung refrigerator here is how to correct it. What OF means is your freezer and refrigerator has or is going to stop and warm up. How it gets activated I don't know. To correct it push the Light+Freezer buttons for 3 seconds. It will reset to the last temp settings and everything should go back to normal.

Samsung... | Answered on May 07, 2020

Not finding what you are looking for?
Refrigerators Logo

173,120 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Refrigerators Experts

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Brad Brown

Level 3 Expert

18336 Answers

Are you a Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...