Hammering Repair Questions, Solutions & Tips - Vr2020

Hammering - Recent Questions, Troubleshooting & Support


181490-7 grease 30g 1 pcs complete be shure there are no cured o-rings or bad gaskets .

188015-8 its the maintenance kit for the service it contains already this 30 grams grease, where come 60 grams advise ? i like also to use some more grease by this heavy kind of hammers. But tools like Hilti with liquid (oil) lubrication and very tight tolerance ball bearings if there is to much (turmopol) oil used it will be damaged, and too little oil also its calculated. I cannot give garantee that 60 grams are advised by a makita service, if you order a maintenace kit ask the seller about why it only contains 30grams. The information to use 60 grams ? doubt.

Makita HM1810... | Answered on Oct 02, 2018


254031-3 pos14 part inlay key can be damaged pos 11 drive rod 315146-2 can broken IF mechanical damage or dried out by leaking gasket / orings.
For better repair use after a repair of some parts an maintenance kit 193394-1 If the working hours are on it, but also after an repair on other parts because leaking tools can be dried out and give cured o rings in a very short time by building up overheat temperature inside and will not build up pneumatic power it will not do the job and is not good for physical strain.

Makita Hammering | Answered on Oct 02, 2018


The GREASE for this heavy jackhammer
Makita 181490-7 Grease (if there are short carbon brushes to find ) replace all orings gaskets (and looking for an maintenance kit for this machine) 188015-8 thats the better way to service.

Makita Hammering | Answered on Sep 12, 2018


It is hard to understand what you are asking, however I have found that with the SDS drills one does NOT want to crowd them but just let the tool work with light pressure...

Bosch SDS-plus... | Answered on Sep 11, 2018


Buy a new switch the old switch was modificated by an maintenance kit if you have an old blue or red real Kango from England. or black Atlas Copco .
But if you have the red Milwaukee Kango then there is only a new switch to replace.

Hammering | Answered on Aug 28, 2018


  1. The total condition of the seal anvil piston and striker are very important for the total condition of impact when spending a service kit (maintenance) when there is leakage at the front part everything will be hot inside and the rings will harden again quickly.


kango 900 950 round switch housing

Hammering | Answered on Aug 16, 2018


Beware for all not all parts are more available, there is no oil used only Grease
Service Pack 1617000036 for Bosch Power Tool eReplacement Parts

Bosch Hammering | Answered on Aug 12, 2018


Connecting rod
Part Number:
315419-3
or
Woodruff Key 4
Part Number: 254001-2
Makita HM1211B Parts List and Diagram eReplacementParts com
Or broken spindle/ worn bearing(s)

Makita Hammering | Answered on Aug 12, 2018


There is no question here

Hammering | Answered on Aug 03, 2018


Spay it with WD40 penetration fluid.

Hammering | Answered on Jul 24, 2018




193243-2 revision maintenance service kit With all necessary rings and fat , beware before ordering an service kit take the time to remove all parts of the spindle ringing on the hammer tube spindle for cracks the chisel sds impact bold striker must be even air-tight on the chisel impact bold not leaking grease out of it , if its leaking the air flow will burn the o-rings in a very early time because of the building heat made by the leaking airflow . and loose of lubrication. fat grease .

Makita HM1100C... | Answered on Jul 11, 2018


burning motor
take it in for a check or junk it

Makita Hammering | Answered on Jul 07, 2018


How much do you put in?

Bosch SDS-plus... | Answered on Jun 27, 2018


Contact Arksen directly with your request.

Hammering | Answered on Jun 26, 2018


The efficient design of Ingersoll Rand 114GQC Air Hammer allows the users to quickly change the spindles on the drill. It is able to deliver 2-5/8 inches of strokes with a BPM speed of 3500 so it ensures total efficiency.

Bosch Hammering | Answered on Jun 07, 2018


BLACK+DECKER drill quickly replaced my cordless drill for all of the heavy duty tasks, and it continues to be a great "work horse". More details about the drill Best Hammer Drill

black-decker-dr670-hammer-drill-vqugf4lgsewrsyjnp2d3onew-4-0.jpg

Hammering | Answered on Jun 04, 2018


Hi
your pressure switch is bad. so it isnt cutting off the compressor. the part number is N003306SV and can be obtained from Dewalt on Servicenet.
Detail

Good luck and hope this helps

Dewalt D55141... | Answered on Apr 11, 2018

Not finding what you are looking for?
Hammering Logo

1,757 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Hammering Experts

John Trevino

Level 3 Expert

1395 Answers

Steve

Level 3 Expert

3289 Answers

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

1995 Answers

Are you a Hammering Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...