Dryers - Recent Questions, Troubleshooting & Support


stop putting them in your pockets before you wash and dry your clothes. ... Look around in the tub of the drier and see if there is something plastic and black that is coming apart in the tub or around the tub. Replace the part that is falling apart.

Dryers | Answered 19 hours ago


LED is not a bulb it is a light emitting diode can only be replaced using soldering iron its an electronic component not a bulb!!!

Dryers | Answered 23 hours ago


Sounds like you've got a bad motor.

Roper REX4634KQ... | Answered Yesterday


Hi
just reversed the doors in 15-20 mins. It worked for me. You do need to be a competent DIYer to do this.
If in doubt, do now't. Get in an engineer

Disconnect from mains (obviously)
Remove top using 7mm nut driver/spanner
Remove 2 cross-head screws holding the door - Door will come away from dryer.
Remove 2 cross-head screws holding the white top and bottom blanking plates
pull out the switch blanking plate
Locate the PINK wires connecting the switch/latch mechanism inside the dryer at the top. This will be taped to a blue wire.
Unscrew the 2 smaller cross-head screws holding the latch/switch assembly whilst holding the pink wire to stop the mechanism dropping inside the dryer.
Pull up the latch mechanism and unravel the black tape holding it to the blue wire.
Drop the latch assembly down the lefthand side of the dryer and refit using the 2 small cross-head screws.
Retape to the blue wier and feed the PINK wires through the plastic retainers.
Fit the white blanking plates to the RIGHT handside of the door opening.
Swap the hinges and the switch latch on the door (don't lose the spring !!!, refitting the hinge blanking plates(ease these out with a small flathead screwdriver covered witha bit of insulating tape to avoid damage.)
Fit the door using the 2 cross-head screws you have left
Refit the top.

Connect to the mains and switch on to the sound of £80 you have just saved yourself !!

Electricity kills Be careful

Whirlpool... | Answered Yesterday


To the user Vince Noir who commented on this - massive THANKS! It was a real wrangle getting the switch (attached to just the x2 pink wires) up and out of the left side and over to the right side but got there in the end.

You'll have to remove a good few things to get the room to be able to move it from one side to the other but it is doable just remember what bolt goes where and don't be too forceful 'snapping' plastic clips in and out.

Next time I get a tumble dryer I'll be gettin one with the switch in the middle!

Note- the switch is the 'latch' that the door goes into. It's wired in cos it makes the machine stop when the door is opened.


Thanks again.

Dryers | Answered Yesterday


WITHOUT A MAKE (BRAND) WE CAN NOT LOOK FOR ERROR CODES SO I SUGGEST YOU DO IT YOUR SELF

Dryers | Answered Yesterday


The glass dome is tightened firmly in the factory, so removal is difficult. When removal is attempted to, the metal housing to which the dome is attached will spin with it, making removal impossible. To see what I'm talking about, look in the small space between the dome and the bottom of the blade housing - it looks like a metal flange, but this is only the bottom of the reflective metal canister that holds the light. Note that there are 4 "dimples" around the circumference of this housing, facing inward. These dimples are what hold the glass dome in place. The trick is to use a rigid piece of wood or metal about the size of a 12" ruler and place the corner of that ruler in one of those dimples - FIRMLY. Then, a second person can get some leverage on the glass dome and "unscrew" it from the housing (counter-clockwise). The purpose of holding the ruler-sized material against the dimple is to keep the housing from spinning with the dome. This is easier said than done, but it will work.

Minka Concept II... | Answered Yesterday


MIGHT TRY ASKING THE MFG'S WEBSITE . WE HAVE NO CLUE WHAT YOU HAVE HERE

Dryers | Answered 2 days ago


SORRY BUT FIXYA DOES NOT SOURCE PARTS , CHECK WITH THE MFG'S WEBSITE

Dryers | Answered 2 days ago


Contact Hunter directly to request it.

Hunter Dryers | Answered 2 days ago


WE OFFER NO ASSISTANCE TO SOMETHING WE DO NOT KNOW WHAT IT IS . ONLY A DRYER WITH 7 BEEPS TELLS ME NOTHING

Dryers | Answered 2 days ago


Clean filter and then again the problem happends please contact to customer care

Whirlpool Dryers | Answered 2 days ago

Not finding what you are looking for?
Dryers Logo

115,897 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Dryers Experts

Marvin
Marvin

Level 3 Expert

83959 Answers

Craig Butler
Craig Butler

Level 3 Expert

1730 Answers

Brad Brown

Level 3 Expert

17978 Answers

Are you a Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...