Question about Refrigerators

1 Answer

I've got a Kenwood KTLD60X15 fridge. As the door is closing the alarm goes off & the display flashes -88. It's only just started doing this last night. The fridge is just over a year old

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Vr2020 Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Refrigerators Master
  • 5,007 Answers

Your unit had sensed that temps are too high. This can be caused by a number of reasons. Call service

Posted on Oct 11, 2018

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 263 Answers

SOURCE: Whirlpool Frost Free 460 door open alarm

http://www.repairclinic.com check how to repace it with the schematic diagrams you'll see how

Posted on Jan 01, 2008

  • 1 Answer

SOURCE: Fisher and Paykel model RF610

The F24 error show that the sensor in the ice maker is out of normal ranges. The usual fix is to replace the sensor in the ice maker.  Also worth checking it to see is the water to the ice maker has frozen up in the value (switch the fridge off for a day). If the error still exists after that you will need to replace the ice maker sensor. You have a 2 year warranty on these parts so the fix should be free.

Posted on Mar 24, 2009

  • 363 Answers

SOURCE: LG Fridge door constantly beeping when closed

On the display panel press the right key that turns the door alarm on and off

Posted on Jul 21, 2009

bigjohn007
  • 425 Answers

SOURCE: The alarm beeper keeps beeping even though the

hi,

you can check a limit switch at its door. it is located usually at the door area inside.
maybe it is not working already or get stuck that is why it doesn't sense that the door is closed.

most of the time it is getting stuck and you can fix it by just pulling it out or other ways to do it.

hope that solves your problem.

Don't forget to rate me. Thanks...

Regards,
John

Posted on Jan 10, 2011

budmrtn
  • 11361 Answers

SOURCE: My Vizio is 4 years old. Last night when we turned

We need to find out the strobe effect is due to the T-CON board is turning on and off or if the backlights is turning on and off. This can also be due to unstable power supply due to bad caps.
You need to look at the back of the screen to see if the light coming through on the back side of the LCD panel is stable when the picture is strobing.
If you are going to DIY and have proper tools, electronics knowledge, and know safety precaution then please read on:

Basic LCD monitor and TV troubleshooting guide:
http://vr2020.cn/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide
http://vr2020.cn/support/r6150077-basic_lcd_monitors_troubleshooting
http://vr2020.cn/support/r7406380-tv_training_manuals
Failed TV and Monitors: http://s807.photobucket.com/albums/yy352/budm
Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague
Parts: www.shopjimmy.com
Capacitors kit: http://lcdalternatives.auctivacommerce.com/Default.aspx he can make you a set of caps.
Or www.digikey.com, just make sure to use caps with low ESR, 105c, high ripple current and long life rating such as PANASONIC FM or FC series.
Please post back what you find.
Please leave rating if it helps.

Posted on Mar 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a GE Profile Series PYE22PSHSS 22.1 cu. ft. Counter-Depth French-Door Fridge. The door adjar alarm used to sound off a chime (which I turned on and set to high in the settings). It has suddenly...


Hey I get it understand what you're asking about the alarm can be disabled by pressing a sequence of buttons at the push-button controls on the front of the fridge I don't know exactly which ones they are but if you look for the alarm it'll be written sideways and small near the normal button

Mar 07, 2018 | GE Refrigerators

1 Answer

Our fridge compressor won't run after a power outage, can it be reset?


compressors use a small start / run capacitor to start the compressor
modern fridges do not like spikes from power outages and many power boards and electronic components fail because of this and I am inclined top use a surge protector before the fridge cord plug
I went google and typed in --fault code 88-88 for samsung fridge model rf26aewp and the first site up is error codes /messages/ blinking
the site is support-us.samsung>popup>iframe
there is a detailed answer there with a list of fault codes as well and what they indicate
there are other sites that also refer to the fault that you have

Dec 15, 2015 | Samsung RF267AEWP - 26 cu. ft. French Door...

1 Answer

Have to slam freezer door to clear 88 error codes on samsung refrigerator


I am not certain on this, but my guess is that you have a problem with the door closed sensor, which should be attached to the door/ light actuating button. It may be faulty, or just out of adjustment. I assume that you have contacted Samsung about what error code 88 is. Do they have any other input? What doesn't make sense is that the fridge turns off. You would think that if the door sensor read "Open door" it would continuously run, rather than shutting off, unless it is causing an overload, or overheating condition. I have had good luck w/ Samsung tech dept., but they can be a little hard to reach. Hope this helps.

Mar 10, 2014 | Refrigerators

2 Answers

Samsung side by side RFG297AAWP display shows 88 88


Press and hold the energy saver button, and the lighting button at the same time until it beeps and clears, 10 seconds. When it goes back to normal panel do the same thing again which will put the fridge in a running diagnosis mode and see if any parts of the 8's are flashing, if so look on the back of the fridge at the error codes.

Nov 24, 2011 | Samsung RFG297AAWP Side by Side Bottom...

1 Answer

I have a 6 y.o. whirlpool fridge wbm 46 model that's started to make a loud buzzing/whirring noise every 15 minutes or so ( only lasts a few seconds each time). It's started doing that noise in the last...


Hi

The sound from your refrigerator can be caused due to various reasons,please check this link bellow to troubleshoot your problem:-

http://www.repairclinic.com/Refrigerator-Troubleshooting?red=Refrigerator-Repair-Help#itsnoisy

Please get back to us if you have further query else please accept the suggestion.

Thank you for contacting fixya.com





Apr 02, 2011 | Whirlpool Refrigerators

3 Answers

GE PFSS6PKW display shows "88" on freezer side and


my fridge had the same prob thank you very much this really works i pressed the energy and alarm for 10 seconds and works PERFECT

Nov 15, 2010 | GE Refrigerators

1 Answer

I have a 55 plate VW Golf 2.0 Fsi - the alarm keeps going off by itself! We disconnected the battery last night (to get some sleep!) and it's started again today.... agh, HELP!


You probably have a faulty door,boot or bonnet lock.If you put the inside light switch to the setting for the light to come on when the doors are open,close all the doors and see if the light goes off.If your model golf has a display on the dash,it shuold tell you which door is open.It could also be a faulty interior sensor or a faulty alarm horn.A diagnostic machine will be able to tell you which was the last alarm activation.

Aug 29, 2009 | 2004 Volkswagen Golf

1 Answer

LG Fridge door constantly beeping when closed


On the display panel press the right key that turns the door alarm on and off

Jul 10, 2009 | LG LFC25760ST 25 Cu. Ft. Panorama French...

3 Answers

How do i reprogram my HV board?


HERE TIS RIGHT OFF THE INSTRUCTION SHEET.  THE TECH JUST LEFT. POWER UP REF. PROGRAM CODE IS LOCATED ON SERIAL PLATE ON THIS UNIT AFTER THE WORD CODE.-1. PRESS & HOLD THE DOOR ALARM KEYPAD.-2. PRESS & HOLD FREEZER TEMP DOWN KEYPAD.-3. RELEASE DOOR ALARM KEYPAD AND WAIT 3 SECS.-4.CONTROL WILL DISPLAY PE TO INDICATE PROGRAMMING MODE-5. ENTRY IS CONFIRMED BY PRESSING TEMP DOWN - KEYPAD ONCE MORE.-CONTROL WILL DISPLAY CURRENT PROGRAM CODE. THIS VALUE SHOULD BE VALIDATED THE THE PROGRAM CODE PRINTED ON UNIT SERIAL PLATE.-NOTE: IF PROGRAM CODE IS CORRECT, THE PROGRAMMING MODE IS EXITED BY CLOSING THE FRIG DOOR.-7.PRESS REFRIG TEMP UP KEYPAD + OR REFRIG DOWN KEYPAD -TO CHANGE THE DIGIT VALUE WITH EACH KEY PRESS.-8.THE DECIMAL POINT INDICATES THE SELECTED DIGIT. PRESS THE FREEZER TEMP UP KEYPAD + TO SELECT NEXT DIGIT.-9.ONCE DEIRED PROGRAM CODE IS DISPLAYED, PRESS AND HOLD THE FREZZER TEMP DOWN KEYPAD - UNTIL UNIT PROGRAM CODE BEGINS FLASHING INDICATING IT HAS BEEN SAVED. *note* IF YOU ATTEMPT TO ENTER AN INVALID PROGRAM CODE, THE CONTROL WILL NOT SAVE THE NEW CODE, BUT WILL BEEP! (THE UNIT WILL NOT RUN RUN WITH A UNIT PROGRAM CODE OF 0000). ONCE THE PROGRAM CODE HAS BEEN SAVED THE PROGRAMMING MODE IS EXITED BY CLOSING THE FRIG DOORS. 

Oct 26, 2007 | Maytag MFI2568AES Stainless Steel Bottom...

Not finding what you are looking for?
Refrigerators Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Refrigerators Experts

John Tripp
John Tripp

Level 3 Expert

4655 Answers

Marvin
Marvin

Level 3 Expert

83779 Answers

Brad Brown

Level 3 Expert

17749 Answers

Are you a Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...