20 Most Recent GE Spacemaker GTUP240EMWW 24" Electric Laundry Center with 2.2 cu. ft. Washer, 4.4 cu. ft. Dryer, 9 Questions & Answers


Some have a nut that holds agitator in place. If it does, it would be under top removable agitator cap. If there is no nut, agitator snaps off by slipping fingers under agitator at 3 and 9 o’clock positions and pulling up hard and fast.

GE Washing... | Answered 2 days ago


Tub bearing and seal is either worn or improperly installed.

GE Washing... | Answered on Dec 10, 2018


The H20 error is a low-water flow error. It could be a problem at the inlet (shut-off closed, low flow through the hoses), the inlet valves, the pressure sensor/air tube that checks how much water arrived in the tub in about 8 minutes or a problem with the controller getting the correct messages.

Since some water arrived in the washer, close the shut-off valves and take the hoses off. Check for debris in the filters (in the hoses and the inlet valves on the washer). Put a bucket under the hoses and check the water flow from each hose. If you have low water flow, replace the hoses and check for any other places that could be clogged or leak. Make sure that the drain hose outlet isn't below the normal fill level in the washer.

Check the pressure system and reed switch that determine the amount of water in the tub. If the air tube is clogged, remove the blockage. Check that the inlet valves are opening and closing properly. Finally, check that the control board and wiring to make sure that the water level signals are reaching the control board. For some GE washers, there is a reset for the control board that is described on the diagnostic sheet inside the washer near the control panel. Try to reset the error message following the directions.

I hope this helps. Please add a comment with the model of the washer for further instructions on testing for and finding the problem.

Cindy Wells

GE Washing... | Answered on Dec 08, 2018


Did you replace main control board or motor control board?

GE Washing... | Answered on Dec 07, 2018


Check on line normally the manufacturer will have the book or pictures on there site

GE Washing... | Answered on Nov 10, 2018


Parts #: WH12X25294 location #632 located at motor plug in area

WH12X26330 - GE Washer Speed Sensor from Parts Dr.
GE
Washer Speed Sensor. This is a new GENUINE GE replacement part.
See more details at Parts Dr. »
+$7.49 shipping. No tax
Parts Dr.
96% positive (5,377)

GE Washing... | Answered on Nov 08, 2018


Check hose and valve screens for debris

GE Washing... | Answered on Nov 04, 2018


No it work with th electronics so the machine will operate and reset for each load

GE Washing... | Answered on Nov 03, 2018


Could be agitator itself making noises, could be transmission noise, maybe timer movement you’re hearing. Hard to say. Probably need someone reputable to check it.

GE Washing... | Answered on Nov 01, 2018

Not finding what you are looking for?
GE Spacemaker GTUP240EMWW 24" Electric Laundry Center with 2.2 cu. ft. Washer, 4.4 cu. ft. Dryer, 9 Logo

2 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top GE Washing Machines Experts

Marvin
Marvin

Level 3 Expert

83810 Answers

geapptech

Level 2 Expert

153 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1474 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

GE Washing Machines

  • GE Washing Machines

Most Popular Question

ge washer top load model ghwn4260d0ww

  • Washing Machines
Loading...