Question about Yamaha Motorcycles

1 Answer

Does every year pw80 engine stays the same

Looking for a piston kit for my sons 2011 pw80.But every one reads "fit until 2006".Will it fit my 2011

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Yamaha Master
  • 339 Answers

Basically, Yes! Almost all of the engine components(and most other things) are interchangeable, some of the first(oldest) models and some of the latest(newest) PW80's have some differences but as long as you stick to one that basically loks the same or around the same year as yours you should be fine, but most Engine Parts are the same! Don't forget you can take the factory installed "plug" out of the exhaust for more power if you want/need a little more!


does every year pw80 engine stays the same - d8464908-0716-46a8-840e-9f67427755b3-pujhmq5yz2fla13a1caeolco-4-0.jpeg

Posted on Feb 28, 2019

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 252 Answers

SOURCE: I want to replace the

here is web site

http://www.partstree.com/parts/?lc=husqvarna&mn=576+XP+EPA+%282009-01%29&dn=90_07_0045

576 xp 2009 parts should fit on 575 xp to s/n up to 081700001

but do x ref on parts 1st before purchase

these were on the 2009 576 - service update #1 in that list

check stroke and piston sizes carefully


cheers



Posted on Aug 08, 2010

  • 43 Answers

SOURCE: Rear brake piston on 2011 Ford Flex SEL. I have done brakes in the past, and never on A Flex. Not for years actually. Seemed ok until I went to compress the piston with a c-clamp. It won't budge. So I

yes, you need to turn the piston to get it back into the caliper, Harbor Freight has this tool and it's not very expensive and works great. Disc Brake Pad and Caliper Service Tool Kit 18 Pc

Posted on Mar 02, 2015

Testimonial: "Thank you!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

A 359 husky. What is the size engine in mm.? Do they make a cylinder, piston kit that Inc gaskets. YEARS IN PRODUCTION?


2001 thru 2011
aprox 47mm
Piston and Cylinder kits from Husky do not include gaskets, but can be purchased individually.

I’m happy to assist further over the phone at https://www.6ya.com/expert/rolandw_c013176d62ee17ae

Dec 04, 2016 | Husqvarna Garden

1 Answer

I need an engine rebuild kit for a SX66 Baumr ag chainsaw is there such a kit? Corrie


if you can't find one , be aware that the piston and ring will be generic fit for that cc engine so go to a mower shop with the bits and see if you can get alternate parts
for example I have homelite piston and ring in a husqvarna trimmer for the last 5 years and still starts and runs ok
as long as the bore size is the same and the wrist pin fits in the piston

Jul 11, 2016 | Garden

2 Answers

Rear brake piston on 2011 Ford Flex SEL. I have done brakes in the past, and never on A Flex. Not for years actually. Seemed ok until I went to compress the piston with a c-clamp. It won't budge. So I came...


you need a tool to turn the piston to get it to go back into the caliper. if you don`t have the proper tool you can use a pair of adjustable pliers to turn the piston back but be careful to not damage the piston rubber boot.

Mar 02, 2015 | Ford Cars & Trucks

1 Answer

2003 mercedes benz start up everything ok step on the brake and BAS/ESP light goes on and stays on had a similar problem a few years ago which turned out to be the rear brake lite was out


These have many sensors, without the code to begin helping you trouble shoot with I would say start by looking at the Power booser for the brakes, it has several sensors installed, are they broken or unplugged?

(I'm assiming you checked the brake lights)

Is the engine light on? There are also engine and transmission codes that will trigger this event as well, all must be followed through with proper diagnostic procedures.

Jun 18, 2014 | Mercedes Ml Ml320 Ml350 Ml550 Ml63 Chrome...

1 Answer

Is the yamaha 2011 and the 2006 frame the same


You might try using a ruler between the bolt holes to see if they are the same distance apart on both parts. If you don't want to do that, call a wrecking yard and ask them to look up interchangeable parts. They can do that for cars, why not bikes?

Nov 28, 2013 | 2011 Yamaha XMax 125

1 Answer

Hi, My son's Yamaha PW 80 (2005) runs very well


I cant answer why it is doing this but i can tell you that my son has a 2004 pw80 which he rides for hours on end with no problem.

Oct 30, 2013 | 2007 Yamaha PW80

1 Answer

What do u think it will be if my pw80 motorbike starts buts but cuts out after hard braking


Hi, Anonymous and the usual suspects are:
1. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
2. Failed alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. Failed main circuit breaker or ignition switch, check for loose connections and continuity.
5. Failed system and or ignition relay, check for continuity.
6. Failed ignition coil, ignition/electronic module.
7. Failed CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Air/fuel mixture screw improperly adjusted.
10. Accelerator pump damaged or not working.
11. Water or dirt in the fuel system, carburetor or filter.
12. Restricted, blocked or kinked fuel line.
13. Fuel tank empty.
14. The gas cap is not venting properly or fuel tank venting system blocked.
15. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
16. Needle and seat stuck closed in the float bowl.
For more information about your issue and valuable "FREE" downloads that you need please click on the links below. Good luck and have a nice day.
Dirt Rider Magazine
Advice My Son first bike PW80 Page 2
YAMAHA PW80 Owner Service Manual
OEM parts for Yamaha
YAMAHA PW80 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Apr 30, 2013 | 2011 Yamaha PW80

1 Answer

Pw80 oil coming out the exhaust


Hi, Anonymous and the usual suspects are:
1. Engine oil over filled.
2. Piston rings worn past service specs.
3. Broken piston rings.
4. Piston pin retaining clip failure.
5. Cracked piston.
6. Broken piston ring lands.
7. Hole in the piston.
8. Valve/guide clearance worn past service specs.
9. Worn out valve seals.
10. Crushed or loose valve seal.
11. Gouges in cylinder walls.
12. Cracked cylinder or head.
13. Blown head gasket.
14. Crankcase breather blocked or hose pinched.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
HELP have oil coming out of my PW80 Exhaust
Excess oil out exhaust pipe
YAMAHA PW80 Owner Service Manual
OEM parts for Yamaha
YAMAHA PW80 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Apr 20, 2012 | 2004 Yamaha PW 80

1 Answer

2011 Yamaha PW80 clutch adjustment


Hi, Pigdog1 for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
PW50 clutch adjustment
how to replace motorcycle clutch
YAMAHA PW80 Owner Service Manual
OEM parts for Yamaha
Yamaha PW80 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Sep 04, 2011 | 2011 Yamaha PW80

1 Answer

My pw80 has a ceased motor. I took the head off and there is a lot of surface rust. How do I +go about sorting this outis it possible to get a rebuild kit or is it a write off??


Ebay has piston , ring and gasket kits for about $30. The barrel is cast iron, so if there is no lip a simple hone may do.
I f the barrel is pitted , you will need an oversize piston kit, and a machine shop to bore the barrel to a bigger size.

Jul 13, 2011 | Yamaha Apache RTR 180 Motorcycles

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

142 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

vince

Level 3 Expert

1234 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1165 Answers

D. E. Hev

Level 3 Expert

1187 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...