Honda Motorcycles - Answered Questions & Fixed Issues


Sounds like it may have a fuel restriction. Check the fuel pressure at the fuel rail. Look for damaged fuel lines or a line that is close to an exhaust system. Possible a fuel pump going out. Does it do this when you are low on fuel and not when the tank is full? If so then the pump is overheating because the fuel is too low and not helping to cool the pump.

Honda... | Answered on Jul 09, 2020 | 20 views


Hi, Michael it should be noted that the reasons your FI light stays on constantly or flashes and your bike will or will not start and may turn over or may not and run great or sputter, these conditions will vary from bike to bike depending on the year, make, and model and you should always refer to your owners/service manual for proper diagnostic procedures. It should also be noted that any type of prior work done to the bike or an abnormal event occurrence IE: adding accessories, electrical curiosity/adventures, laying the bike down/crashes, rain storms/bike washings just before FI light issues started can be significant hints/aids into tracking down the gremlin, also carry the appropriate jumper wire to access fault codes to reduce the risk of being stranded or towed. The newer the bike the more sensitive the ECM becomes and will not let the bike start when aftermarket accessories have been installed without being reprogrammed. That being said the usual suspects are:
1. Faulty Fuel Pump, fuse or system relay switch.
2. Battery starting to fail due to old age/damage, perform a load test.
3. A discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Faulty safety switches/sensors: run/off, ignition, clutch lever, neutral, side stand, tip over, fuel, and or their connections.
5. Broken wire or worn insulation exposing wire to a ground situation especially inside wire harness at tight bends around fairing brackets, under dash panels, under fuel tanks over cylinder heads, etc. Many harnesses are open on the ends that will allow water to enter and accumulate at v-bends.
Dielectric grease and contact cleaner are your best friends for wire/cable/harness connectors, look for corroded, broken, or loose pins/sockets.
6. Installation of aftermarket accessories ie. exhaust systems, mufflers, air cleaners, fuel tuners, electrical component, etc.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.vfrdiscussion.com/index.php?/forums/topic/16-fi-light-how-to-read-error-codes/
https://www.bikechatforums.com/viewtopic.php?t=313667
https://www.carlsalter.com/all-motorcycle-manuals.asp
https://www.partsfish.com/page/oem-parts-for-honda
https://powersports.honda.com/downloads/owners-manuals

Honda... | Answered on Jul 08, 2020 | 19 views


https://www.youtube.com/watch?v=Xrn58yenvBs
If you have clutch master cylinder and slave cylinder might need bleed air out.
https://www.youtube.com/watch?v=wCj8QiIo4ss
Remember when bleeding brakes keep the master cylinder full of oil or you will suck air back in line. Should have 2 hole in bottom of master cylinder. Make sure holes are not plugged. One the fluid goes out the other the fluid comes back in.
https://www.youtube.com/watch?v=YP195yHIsIk
https://www.motorcycleforum.com/threads/hydraulic-clutch-problems-88-honda-shadow.92072/
https://www.youtube.com/watch?v=n2eMTnMhFew



Honda... | Answered on Jul 06, 2020 | 28 views


try adjusting the clutch. maybe its dragging

Honda... | Answered on Jul 03, 2020 | 21 views


Hi, Mattias it should be noted that the reasons your FI light stays on constantly or flashes and your bike will or will not start and may turn over or may not and run great or sputter, these conditions will vary from bike to bike depending on the year, make, and model and you should always refer to your owners/service manual for proper diagnostic procedures. It should also be noted that any type of prior work done to the bike or an abnormal event occurrence IE: adding accessories, electrical curiosity/adventures, laying the bike down/crashes, rain storms/bike washings just before FI light issues started can be significant hints/aids into tracking down the gremlin, also carry the appropriate jumper wire to access fault codes to reduce the risk of being stranded or towed. The newer the bike the more sensitive the ECM becomes and will not let the bike start when aftermarket accessories have been installed without being reprogrammed. That being said the usual suspects are:
1. Faulty Fuel Pump, fuse or system relay switch.
2. Battery starting to fail due to old age/damage, perform a load test.
3. A discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Faulty safety switches/sensors: run/off, ignition, clutch lever, neutral, side stand, tip over, fuel, and or their connections.
5. Broken wire or worn insulation exposing wire to a ground situation especially inside wire harness at tight bends around fairing brackets, under dash panels, under fuel tanks over cylinder heads, etc. Many harnesses are open on the ends that will allow water to enter and accumulate at v-bends.
Dielectric grease and contact cleaner are your best friends for wire/cable/harness connectors, look for corroded, broken, or loose pins/sockets.
6. Installation of aftermarket accessories ie. exhaust systems, mufflers, air cleaners, fuel tuners, electrical component, etc.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.cbrxx.com/threads/fi-warning-light.23109/
http://www.cbr1100xx.org/forums/index.php?/topic/81369-fi-light-stays-on/
https://www.carlsalter.com/download.asp?p=1879
https://www.partsfish.com/page/oem-parts-for-honda
https://www.manualslib.com/manual/677765/Honda-Cbr1100xx.html

Honda... | Answered on Jul 01, 2020 | 27 views


I cleaned up the dreadful text-speak and translated to British English!

The answer is

Fork oil per rod:
108 ML SAE 10W

Make sure you drain the oil after the scooter has been on a run and drain it completely.

https://www.louis.eu/rund-ums-motorrad/bike-datenbank/honda-ses-125-dylan/jf10/1922

Honda... | Answered on Jun 20, 2020 | 27 views


It may due to the loose screw, go to the mechanic.

Honda... | Answered on Jun 10, 2020 | 27 views


Hi, Emackie2004 for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere $15 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
2005 Honda VFR 800 fuse box location Google Search
6 Gen Fuse Box Location
2002 Honda VFR800 VFR800A Interceptor Service Repair Workshop Manual... $15
https://www.partsfish.com/page/oem-parts-for-honda
Honda VFR800A 2005 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2005 Honda VFR... | Answered on Jun 05, 2020 | 631 views


https://www.hondashadow.net/threads/torque-specs.122143/
Read this post for the torque specs on the bolts.

Honda... | Answered on Jun 02, 2020 | 34 views


Hi, spark gap 0.7 all the beat.

Honda... | Answered on Jun 02, 2020 | 28 views


requires fuel spark and air all at the proper time we can not test for you remotely sorry

Honda... | Answered on May 27, 2020 | 63 views


Start taking it apart, cleaning, greasing oiling and putting it back together. Empty all the fuel and replace with fresh. Change the oil and filter. Change the spark plugs. you could have bought a carburettor repair kit. Videos and spares...

https://www.google.com/search?q=2004+Honda+Recon+tm+250cc

Honda... | Answered on May 13, 2020 | 33 views

Not finding what you are looking for?
Honda Logo

Ask a Question

Usually answered in minutes!

Popular Products

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6394 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

richard libby

Level 2 Expert

209 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...