Question about Cars & Trucks
3.5L (LZ4) & 3.9L (LZ9) Engines
The Crankshaft Position (CKP) sensor is located on the right side of the engine, above the transaxle and just below the exhaust manifold
Posted on May 18, 2018
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
It is on the rear of the engine, passenger side. You need to access it from the underside and it is halfway up the block between the head and the oilpan. It is real close to where the engine and transmission meet.
Posted on May 23, 2009
PCV . Positive Crankcase Ventalation Valves are always located in the valve cover pans with a hose attached usually leading to the air cleaner, or some other vacuum source..
Posted on Jun 19, 2009
It mounts in the side of the block near the crankshaft,it fits in a hole,going into the engine block.,look on the inside of the engine compartment ,on the firewall side,left of the pulleys,down low.
Posted on Mar 22, 2010
SOURCE: 2004 3.8 Chevy impala sensor
The crankshaft positions sensor is located behind the crankwheel on the
passenger side of the engine. In order to replace it or at least
examine it, a person would need to remover the crankwheel with a puller
that can be rented out at Autozone. Just ask for a harmonic balancer
puller. Remove the front right tire and place firmly on jackstands. The
crankshaft pulley WILL NOT loosen by just turning the bolt. This is a
two person job. Caddycorner to the starter, there is a small plastic
plate cover that covers the driveplate/flexplate. Remove the two bolts
and pull the cover off. Have one person position a screwdriver into the
ring gear teeth and have another remove the pulley bolt. Its EXTREMELY
TIGHT and the best way to remove it is with a large rachet and a breaker
bar. Once the bolt is removed, take the puller and position
accoridngly. The threaded holes are not on the surface but inside the
pulley itself. Place large bolt in center of the puller and place the
pointed or flat tip on center of the large bolt and place. Take three
very small screws or bolts that came with the puller and position all
three in place. Once all this is done begin turning the bolt in the
middle of the puller clockwise. This will take alot of arm strength and
anywhere from 15-30 min to do. Once the wheel has come off, carefully
pry off the sensor cover which is another piece of plactic. Once the
cover is off, carefully remove the sensor and examine or replace as
needed. Installation is reverse of removal. Hope this helps
Read more: http://wiki.answers.com/Q/Where_is_the_crankshaft_position_sensor_on_2001_Impala#ixzz1xaQZV1IR
Posted on Jun 12, 2012
Testimonial: "Thanks a lot... I'll be taking it to a shop. "
Tips for a great answer:
Apr 08, 2018 | Cars & Trucks
Apr 22, 2017 | 2004 Chevrolet Impala
Aug 24, 2016 | 2010 Chevrolet Impala LT
Nov 13, 2015 | Cars & Trucks
Mar 09, 2015 | 2009 Chevrolet Impala
Nov 09, 2014 | 2009 Chevrolet Impala
Feb 03, 2012 | 2006 Chevrolet Impala
Dec 29, 2010 | 2000 Chevrolet Impala
Nov 26, 2009 | 2006 Chevrolet Impala
Aug 23, 2019 | Cars & Trucks
341 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: